Lexmark Cn. Network. Service Manual. xxx. Assembly 1: Operator panel assembly, Cdn/Cn/Cdn. 6. 40X 1. 1. Bezel. Lexmark C Pdf User Manuals. View online or download Lexmark C User Manual, Troubleshooting Manual, Quick Reference. View and Download Lexmark C service manual online. Service Manual. C Printer pdf manual download. Also for: Cn, C, C, C, C

Author: Gugrel Goltirr
Country: South Africa
Language: English (Spanish)
Genre: Software
Published (Last): 7 August 2014
Pages: 156
PDF File Size: 16.63 Mb
ePub File Size: 15.91 Mb
ISBN: 645-1-22306-471-9
Downloads: 6186
Price: Free* [*Free Regsitration Required]
Uploader: Togore

Select Single or Continuous. Page 26 xxx Service error codes and paper jam messages continued Error code Description Action Wait for the fuser to cool before clearing jams from this area.

A 2 Phillips screwdriver is needed to attach the hard disk to the mounting plate. Cancel a job appears, and then press Canceling a print job from the Windows taskbar When you send a job to print, a small printer icon appears in the right corner of the taskbar.

The illustration shows the possible jam areas. Lexmark C Service Manual pages. When installing, make sure the top half E of the spring is under the straight spring F.

Not shown in the Asm-Index column indicates that the part is procurable but is not pictured in the illustration. Page 73 xxx Print quality—blurred or fuzzy print Blurred or fuzzy print is usually caused by a problem in the EP drive assembly or in the transfer belt assembly. Do not go to step 2 until T and Z are aligned.


Print Directory Menu Replace the paper pick Go to step 2. Remove the seven screws B securing the inner access cover.


The 4 pack will suit people doing mainly colour printing. System Card network —models C53x Remove the fuser, and check the camshaft C53n2 to step 3.

Remove the mounting screw G and the cap H. Power Saver appears, and then press Using the numeric keypad, enter the number of minutes for the printer to wait before entering the Power Saver mode.

Page xxx Bump aligner leexmark The power to turn the bump aligner roll is supplied from the bump aligner lexmarrk. This manual also for: Ready appears on the display.

Page xxx Transfer belt drive The transfer belt unit receives drive from a motor located on the EP drive assembly. Input Sensor Service Check Notices Lexington, KentuckyU. Restoring Factory Defaults Cancel Not Available The media being used does not meet the printer specifications.

Lexmark CN – C Color Laser Printer Manuals

Disconnect the transfer belt cable A. Blinking green Printer is warming up, processing maual, or printing a job. Clearing jams behind the inner door If the paper is jammed behind the inner door, but not under the photoconductors, Supported Paper Sizes Lift the small toner cartridge handles slightly and pull straight out.

Solving Print Quality Problems The following models are available. Standard Usb Port Disabled When paper is jammed under the fuser or the fuser cover, Did this solve the problem? Each sheet must be driven past the fuser exit flag and allowed to fall before being turned around and starting the duplex path. Align the tray, and insert it.


Clearing Tray 2 jams If the paper did not feed from Tray 2 correctly, the jam is in the tray. Page xxx Left Toner level sensor High voltage Transfer contact assembly power supply Locations and connectors Shake the cartridge back and forth several times, and then reinstall it. Adjusting Power Saver Power Saver appears, and then press Using the numeric keypad, enter the number of minutes for the printer to wait before entering the Power Saver mode.

Remove Defective Hard Disk Printing A Network Setup Page Printing a network setup page If the printer is attached to a network, print a network setup page to verify the network connection.

Lexmark C520 Service Manual

Some data will continue to be processed while the printer is locked. Access the top two screws through the top cover. The print media is advanced in the paper path onto the transfer belt and is carried along the belt underneath each photoconductor unit. Once locked, the metal plate and the system board cannot be removed. Repeat steps 2 through 11 for yellow and magenta.

Related Posts