FBI XL2T PROGRAM PDF

Introduction The XL-2T is a state of the art microprocessor-based control/ communicator. The system features seven (7) fully programmable zones. Programming. XL-2T. Security System. Installation and Setup Guide. STAY. INSTANT. ACYLB. READY APPENDIX D – SYSTEM PROGRAMMING WORKSHEET. Example: To program phone number enter 1#8#0#0# etc. Exit Program STAY. Default Panel Short “EEPROM RESET” pins on panel and power up system.

Author: Gardakora Nacage
Country: Thailand
Language: English (Spanish)
Genre: Literature
Published (Last): 10 July 2007
Pages: 309
PDF File Size: 8.64 Mb
ePub File Size: 2.23 Mb
ISBN: 884-3-48108-312-8
Downloads: 36458
Price: Free* [*Free Regsitration Required]
Uploader: Zuluramar

By pressing ‘print’ button you progrwm print only current page. Upon detection of the first violation, smoke detector power on conventional 4 wire smoke detectors connected to ZONE modules will be reset for a period of 8 seconds.

The keypads are surface mounted as described below. The alarm was then activated, without me activating it. System Programming Programming Questions This topic defines the programming questions and the values for each question. Keypad Sounder Section 5 – System Operations Keypad Sounder The sounder or loudspeaker housed inside the keypad, emits annunciates sounds according to the condition of the security system.

A user code is required to disarm the system.

After this time period, power is restored. The checkmark highlights which options are selected.

FBII XL-2T Installation And Setup Manual

Enter text from picture: System ready to be armed System not ready to be armed Enter the digit from the table below. Secure keypad to double-gang box as shown in graphic at left.

  CARTA PANTONE UNCOATED PDF

Page 40 Section 5 – System Operations If a user code is not required to set the time, then enter: The keypad will indicate a trouble on the fire zone if the bell or sounder is not properly connected.

The Extended Reporting Format: The following is a quick comparison. Good Day I had a four digit user code, but the last digit was lost. Page 81 – Extended 3×1 Ext. Refer to the Installation Instructions for hookup information. The keypads can be surface mounted or flush mounted as described below. The restore code will also be reported if the system is disarmed during an alarm. Section 5 – System Operations Keypad Sounder The sounder or loudspeaker housed inside the keypad, emits annunciates sounds according to the condition of the security system.

If a keypad tamper code is entered then it will be transmitted to the Central Station. With this device some systems can obtain dial tone in areas which do not automatically provide dial tone.

Section 6 – System Programming When programming the English zone descriptors, use the following techniques to program the characters: Fire Trouble is reported to the CS if enabled program question 32, location 3.

This enables Fire and Burg zones to report restores. Table of Contents Add to my manuals Add. I then pressed code button followed by master codethen user no 3 and then new 4 digit user code. Trigger 1 must be selected for smoke detector power reset for this feature to active.

  FLOYD WARSHALL ALGORITHM EXAMPLE PDF

FBI XL-2T Turbo Program Sheet

A-2 Partial Extended 3×1 Part. The purpose of this manual is to give you a brief overview of the XL-2T control panel, progrsm provide instructions for installing a basic system.

The double-gang box shall be mounted flush with wall in order for keypad screws to fit. For UL installations see wiring diagram for hookup.

For Built-in Siren Driver, connect a single 8 ohm speaker only. The door of the metal cabinet may be removed to make it easier to install the control panel. LCD display keypads will indicate the following message: Question 32, L1 – Bypass Code Directly to a control panel having a keypad cutout on the front of its enclosure. The auto arm time represents the time of day that the area will automatically arm if it is not already armed.

FBI XL-2 Program Sheet

Question 10, L1 – Burglary Bell Time-out Page 23 Fire Trouble is reported to the CS if enabled program question 32, location 3. The system must be in ready mode.

We regret any inconvenience this may have caused and appreciate your continued support of FBII products.

Upon entry to the system log view, LCD based keypads will show the events one at a time starting from the oldest event.

Related Posts