ATTANSIC ATTP1 PDF

, 13, ATTANSIC, -. Kring Electronics Co., Ltd. , -, Attansic, sop8. 63, 0, ATTANSIC, -. Rantle East Electronic. , -, ATTANSIC, SOP. 年12月11日 ATTP1_ – Technology Corporation ATTP1 Over Temperature Please contact Attansic Technology Corp. for the latest documents. Attansic. ATTP1. Tel:. MFG:. ATTANSIC. Picture. D/C:. 09+. QTY:. Packaging:. SOP8L. Package:. Note:. 原装正品. Support. No“ATTP1”Picture.

Author: Kazihn Vikasa
Country: Timor Leste
Language: English (Spanish)
Genre: Business
Published (Last): 10 July 2012
Pages: 96
PDF File Size: 15.95 Mb
ePub File Size: 6.67 Mb
ISBN: 608-6-85891-841-4
Downloads: 56035
Price: Free* [*Free Regsitration Required]
Uploader: Taushura

ATTP1 Attansic CPU thermal protection controller chip SOP8

Check out our sister site! Well, I’ve solved that problem. I’ve personally verified this a few times myself, so I know it works. The time now is It’s already in the right place. You will find that it is easiest to thread the jumper on attansoc diagonal under the CPU socket between the pins.

I find that the edge of a single-edge razor blade works rather well for helping lift this pin while I apply heat with the soldering iron. Find pin 97 of the Winbond chip. As for the other, yes you should solder pin 4 of the Attansic back down to the mobo.

You don’t need to move the jumper though. This is the analog voltage input. The jumper wire will need to be about 3. I just have you solder directly to the pin because it is simpler to explain. Solder to pin 61 first, then pin This is the 5vsb input. Tie the analog voltage supply for the Winbond chip to the 5vsb rail instead of the 5v rail. Soldering on these quad flat packs is a real PITA!

  CASIO CTK 631 MANUAL PDF

Anything else is nearly impossible. Apply a dollop of gel type super glue or some other fastening agent to each of your jumpers to near pin 97 and pin to keep them from flexing too much and breaking the pins off the chip. I will have no sympathy. I’ve got pretty steady hands and it took me three tries to get the jumper soldered correctly without bridging solder to the other pins.

Find pin 61 of the Winbond chip.

However, because of the way the mod is done, the odds of messing it up in such a way that you dissable the OTP function are pretty low. Webb City, Mo Posts: If you have previously modded your mobo to read the thermal diode, you MAY find that your temps are degrees higher than they used to be. Add Thread to del. Find pin of the Winbond chip.

ATTP1 – – IC Chips – Kynix Semiconductor

Lift this pin just as you did pin The possibilities are endless! While this mod works pretty well, it has one glaring drawback, which I mentioned in the previous post: I’ve been looking for developer’s docs for the NF2 chipset and haven’t been able to find any. You’ll find that trying to solder the wires to the broken pins, while not impossible, is exceedingly difficult. In my case, I actually took a chance with my CPU to try it out.

That is one of the reasons I did it the way I did, so that you could undo it if necessary. The original mod involved disabling the Attansic chip protection because simply hooking the thermal diode from the CPU to the Winbond chip would result in the system not powering up, and the familiar two-tone “You’ve got something really mucked up” siren.

  FOELIX BIOLOGY OF SPIDERS PDF

I didn’t think it did. Also make sure that you don’t accidentally bridge any of the adjacent pins with solder while you are trying to lift this pin.

BB code is On. Our members offer you their FAQs! You should thread the jumper first, then solder to the Attansic chip, then finally solder to the Winbond chip. A fine tip soldering iron is definitely a must. However, be aware that soldering pin 97 and pin back down is rather tricky because of the fine spacing of the pins. So what is the solution? The wire will need to be about 8 cm 3″ long. That’s all there is to it. It is the 4th pin from the top right corner of the chip going down the right side of the chip, when viewed as described above.

I use to type in short sentence.

ATTP1_1.3.pdf

This is the top right pin on the Attansic chip, when viewed with the mobo oriented as described above. This means that your poor CPU is going to blow its brains out just as soon as it loses proper cooling for any reason. Make sure you leave just a dollop of solder on the end of the jumper wire when you tin it or you’ll never get it to solder properly but don’t leave too much, or you’ll bridge the pins.

Related Posts