ASTM D885 PDF
ASTM D – Air Permeability of Textile Fabrics . Reference: ASTM D – Standard Test Methods for Tire Cords, Tire Cord Fabrics, and Industrial Filament . ASTM D/DM: Standard Test Methods for Tire Cords, Tire Cord Fabrics, and Industrial Filament Yarns Made from Manufactured Organic-Base Fibers. This standard is issued under the fixed designation D ; the 1 These test methods are under the jurisdiction of ASTM Committee D13 on.
|Published (Last):||22 March 2012|
|PDF File Size:||2.78 Mb|
|ePub File Size:||11.90 Mb|
|Price:||Free* [*Free Regsitration Required]|
This standard may be applied to similar yarns and cords used for reinforcing other rubber goods and for other industrial applications. Bibliography of Tire Cord Test Methods. Concrete, Asphalt and Rock.
ASTM D885 – Tensile Properties of Tire Cords, Tire Cord Fabrics, and Industrial Filament Yarns
Users of previous versions of software such as Bluehill 2 and Bluehill 3 can easily upgrade to the newest aatm of Bluehill. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of d85 limitations prior to use. Instron pneumatic tire cord grips are designed specifically for testing high strength tire cord, and are able to grip securely while maintaining high throughput It is important to review ASTM D to fully understand the test setup, procedure, and results requirements.
Active view current version of standard. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. The values expressed in each system may not be exact equivalents; therefore, each system must be used independently of each other, without combining values in any way. The challenges of testing to this standard are: Extractable Matter in Yarns and Cords.
Width of Tire Cord Fabric.
ASTM D Industrial Filament Yarns Made from Manufactured Organic-Based Fibers – Instron
Gripping of the specimens can prove a challenge, as the cords tested with this standard are designed to be very high strength. They may be applied to similar yarns and cords used for reinforcing other rubber goods and for other industrial applications. Link to Active This link will always route to the current Active version of the d8885.
The test methods apply to nylon, polyester, and rayon yarns and tire cords twisted from such yarns and to fabrics made from such cords. Elongation at Break of Conditioned Yarns and Cords. The result of this test is a determination of tensile strength of the cord being tested. Description Literature Contact Us This standard details the testing of fibers and cords made specifically for use in the manufacture of pneumatic tires.
Combining values from the two systems may result in non-conformance with the standard. CP Rated capacity 5 kN kgf, 1, lbf Suitable for testing a wide range of tire cords, braided wire, tow and mono-filements. Email addresses can only contain letters, numbers and the following special characters: Properties of Tire Cord Fabric.
ASTM D – Tire Cord and Yarn Grip
If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. Onsite Training At Your Facility. Significance and Use, Tensile Properties. Next Checking to see if you are a returning visitor…. Check this box to receive pertinent commercial email from Instron focusing on products, upcoming events, and more! Bluehill Universal Software is built from the ground-up for touch interaction and an intuitive user experience.
SI units is the technically correct name for the system of metric units known as the International System of Units. The methods include testing procedure only and include no specifications or tolerances.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Breaking Toughness of Yarns and Cords. Incorporates a grooved channel for specimen guidance. Significance and Use, General.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Bluehill LE for Basic Testing.
The methods include testing procedure only and include no specifications or tolerances. Modulus of Conditioned Yarns and Cords.
They may be applied to similar yarns and cords used for reinforcing other rubber goods and for other industrial applications. The yarn or cord may be wound on cones, tubes, bobbins, spools, or beams; may be woven into fabric; or may be in some other form. WaveMatrix 2 for Dynamic Testing. As a minimum, test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing.
Historical Version s – view previous versions of standard Translated Version s: Twist in Yarns and Cords. They are designed with standard and optional features that increase testing efficiency and improve the testing experience for the operator.
ASTM D885 Tire Cord Tensile Test
Growth of Conditioned Yarns and Cords. The values stated in either acceptable metric units or other units shall be regarded separately as standard. Contraction of Wet Yarns and Cords.