ASTM D5420 PDF
Gardner Impact ASTM D, D Falling Dart Impact (Gardner Impact) ASTM D, ASTM D Scope: Falling dart impact, also known as Gardner. This standard is issued under the fixed designation D ; the number 1 This test method is under the jurisdiction of ASTM Committee D20 on Plastics. ASTM D Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact).
|Published (Last):||27 November 2012|
|PDF File Size:||15.56 Mb|
|ePub File Size:||5.47 Mb|
|Price:||Free* [*Free Regsitration Required]|
Raise the weight in the tube to the desired impact value, as shown on the appropriate scale, and release it so that the weight drops on the striker. Alternatively, affix testers directly to the? Falling dart impact, also known as Gardner impact, is a traditional method for evaluating the impact strength or toughness of a plastic material.
Assurance Enabling you to identify and mitigate the intrinsic risk in your operations, supply chains and business processes. Different materials respond differently to changes in the velocity of impact.
Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Standards can be obtained from appropriate standards authorities. The values given in parentheses are for information only. A change of a factor of two in the drop height will cause a change of only 1.
Data from only three laboratories were used in calculating the values in these tables. The principles of Use of rubber mats either directly under the tester or supporting apparatus is prohibited.
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
Validating the specifications, value and safety of your raw materials, products and assets. D — Different materials respond differently to changes in the velocity of impact. However, this test method is intended primarily for rating materials under speci? Production parts shall be tested in the as-received condition to determine conformance to speci?
Gardner Impact ASTM D, D
It is the responsibility of the user of this standard aastm establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. NOTE 1—Depth of penetration when fully seated shall be Therefore, factors including surface features?
Certification Formally confirming that your products and services meet all trusted external and internal standards. If a test sample passes, the drop height is increased by one unit.
Machining specimens to reduce thickness variation is not permissible. Astj us a request Wilton UK: Enabling you to identify and mitigate the intrinsic risk in your operations, supply chains and business processes. For optimum results using the staircase method, a minimum of 30 test samples are necessary.
Gardner Impact ASTM D4226, D5420
Historical Version s – view previous versions of standard. Data in these tables are speci?
NOTE 3—Such block dimensions conform to commercially available butcher block tables. See Test Methods D for descriptions of suitable micrometers. Then test the second specimen. If a test sample fails, the drop height is decreased by one unit. Last previous edition approved in as D – It is not necessary to bolt blocks or bases of this weight to the? However, the selection of any one of the striker geometries is permitted, after such consideration.
Each laboratory obtained two test results for a material. The specimens shall be free of obvious imperfections, unless the imperfections constitute a variable under study. Do not apply the data in Table 2 and Table 4 rigorously for acceptance or rejection of a material.
NOTE 4—As few as ten specimens often yield sufficiently reliable estimates of the mean-failure height. However, in such cases the estimated e5420 deviation will be relatively large 1. The values given in brackets are for information only. Material processing can have a significant affect on the development of a plastic’s physical properties.
Consider the end use environment and requirements when choosing from the available striker geometries. Formally confirming that your products and services meet all trusted external and internal standards.
Need help d5240 have a question? Testing Evaluating how your products and services meet and exceed quality, safety, sustainability and performance standards.
ASTM D – GARDNER IMPACT
However, the velocity of a free-falling object is a function of the square root of the drop height. Inspection Validating the specifications, value and safety of your raw materials, products and assets. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Be sure the specimen is?