ASTM A897 PDF

ADI; ASTM AM, ASTM (in-lb units) ASTM M (SI units) Austempered Ductile Iron (ADI) offers low cost, design flexibility. ASTM A is an alloyed nodular iron which is heat treated to achieve the desired properties. Austempered ductile iron (ADI) is a. This standard is issued under the fixed designation A/AM; the number 1 This specification is under the jurisdiction of ASTM Committee A04 on Iron.

Author: Goran Shaktilmaran
Country: Qatar
Language: English (Spanish)
Genre: Software
Published (Last): 25 May 2004
Pages: 342
PDF File Size: 7.79 Mb
ePub File Size: 16.76 Mb
ISBN: 489-9-75799-317-9
Downloads: 65178
Price: Free* [*Free Regsitration Required]
Uploader: Zulule

The chemical composition requirements may be agreed upon between the manufacturer, heat treater, and the purchaser. This shall not prevent the purchaser from also performing any or all of the quality and inspection requirements. Responsibility for meeting the speci?

To see MatWeb’s complete data sheet for this material including material property data, metal x897, material suppliers, etcplease click the button below.

ASTM A897-A897M-16

The proper alloy composition should be determined jointly by the foundry and the heat treating source. Data sheets for overmetals, plastics, ceramics, and composites. Highly specialized in austempered ductile iron. This agreement should include a de? Any of the aforementioned nonconforming conditions will reduce the toughness of an ADI component, even if adequate for conventional ductile iron. asstm

ASTM A ADI Grade / (Grade 2)

Or if you don’t have an account with us yet, then click here to register. Link to Active This link will always route to the current Active version of the standard. Requirements for the microstructure constituents such as graphite, ausferrite acicular ferrite and high carbon, stable austenitepearlite, and martensite are prescribed. The standard specimens for tension and Charpy impact tests are illustrated. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

The following should be met as a minimum: Manganese Manganese additions above that of the base metal composition are not recommended because Mn segregates to the last to freeze regions of the casting and will retard the formation of ausferrite if the nodule count is not sufficiently high to break up the Mn segregated region.

  GANODERMA BONINENSE PDF

Pouring molten grey iron metal from holding furnace into pouring ladle at a grey iron casting company. It is informational only and not an official part asfm the standard; the full text of the standard itself must be referred to for its use and application. Above this level, Cu creates a diffusion barrier around the graphite nodules, thus inhibiting carbon mobility during austenitizing.

Please read our License Agreement regarding materials data and our Privacy Policy. This does not prevent an agreement wherein any one manufacturer in the chain of sequential operations can agree to assume full responsibility for all quality and inspection requirements. Austempered Ductile Iron Case Study.

ASTM A Grade 3 () Austempered Ductile Iron

The composition reported herein does not guarantee ADI properties, nor is it mandatory. It should be controlled as follows in Table X1. Proper purchasing, storage and use of charge materials will minimize the occurrence of carbides and gas defects. Floor, manual, squeezer, cope and drag, Hunter, Sinto and Disa molding processes. Responsibility for Quality and Inspection If you feel asttm your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

We represent the best austempered ductile 8a97 foundries in the USA and back it up with professional aetm ongoing service. The iron shall conform to the mechanical property requirements including tensile strength, yield strength, elongation, impact energy, and Brinell hardness. If too high levels of carbon are present, carbon? Proper molding control will minimize surface defects and other sub-surface discontinuities.

Commonly used in fabrication-to-casting conversion atm, ADI grade 2 offers mechanical performance that is often comparable to steels, without the added cost.

The manufacturer s may require the purchaser to provide written agreement for any changes mutually agreed upon. The matrix in conventional Ductile Iron is a controlled mixture of pearlite and ferrite.

Machining can be done before or after heat treatment. We have found that austempered ductile iron ADI offers the best combination of low cost, design flexibility, good machinability, and a high strength-to-weight ratio as well as good durability, wear resistance and fatigue strength properties.

  GREENSTAR 30SI PDF

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. When separately cast test coupons are used, selection shall be as outlined in Tempered martensitic matrices may be developed for wear resistance, but lack the ductility of either as-cast Ductile Iron or ADI. The data has been submitted. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

In those cases where removal of test bars from actual castings has been agreed upon see Lower temperature quench would give it a higher strength with abrasion resistance.

This quenching rate must exceed some critical value to attain the correct microstructure ausferrite or ausferrite and proeutectoid ferrite. Users requiring more precise data for scientific or engineering calculations can click on the property value to see the original value as well as raw conversions to equivalent units. In case no option is expressed, the manufacturer shall make the choice.

Combining values from the two systems may result in nonconformance with the speci? This makes the material stronger and tougher than heat treated ductile iron. We deal strictly in the sourcing of castings and machined castings. If test bars are to be cut from castings, test bar location shall be agreed upon by the purchaser and the manufacturer and indicated on the casting drawing. Composition guidelines are recommended in Table X1. The average impact energy shall meet the requirement of Table 1.

ADI heat treated materials exhibit mechanical properties equivalent to cast and forged steels.

Subscribe to Premium Services Searches: The amount of certain elements – specifically Cu, Ni, Mo – would be specified by the heat treater for improved heat treatability. The level of Mo should be restricted to not more than 0.

Related Posts