20A UM001 EN P PDF

Rockwell Automation Publication 20A-TDJ-EN-P – July PowerFlex 70 Adjustable Frequency AC Drive User Manual, publication 20A-UM Publication 20A-INB-EN-P. The PowerFlex 70 drive contains protective MOVs and Common Mode. Capacitors referenced to ground (see below). To guard. posts; United States. Posted 1 Jun ยท llautomation. com/idc/groups/literature/documents/um/

Author: Zolorg Akinot
Country: Algeria
Language: English (Spanish)
Genre: Relationship
Published (Last): 17 April 2013
Pages: 218
PDF File Size: 18.13 Mb
ePub File Size: 16.45 Mb
ISBN: 595-2-28814-475-1
Downloads: 72696
Price: Free* [*Free Regsitration Required]
Uploader: Tern

It is very easy to do.

The cause must be corrected before the fault can be cleared. I suspect when you say “how to put original parameters to the new one”, you want to program a new drive ym001 the same parameters as an existing drive.

Rockwell Automation 20A PowerFlex 70 Adjustable Frequency AC Drive User Manual | Page 50 / 56

Also you 20 remove the HMI first before trying to remove the cover of that drive. Posted 31 May Allen-Bradley Drives Technical Support. Create an account or sign in to comment You need to be a member in order to leave a comment Create an account Sign up for a new account in our community. Good luck and be careful. Table of Contents Add to my manuals Add. Comments to this Manuals Your Name. Sign In Sign Up. Posted 1 Jun Go through the existing drive and make note of the value of every parameter.


L Automation distributor or sales representative. Press the Enter key to display the Start-Up Menu. Page of 52 Go.

Chapter 1 has all parameters 02a their parameter groups. To find your local Rockwell Automation distributor, visit. The information provided Does Not replace the User Hm001 and is. With these parameters, you can set the following functions If the Safe-Off board is removed from the drive, pins 3 and 4 of the Safe-Off Connector must be jumpered for the drive to run.

Don’t show me this message again. For detailed PowerFlex 70 information including advanced start-up.

Rockwell Automation 20A PowerFlex 70 Power Jumpers User Manual | 6 pages

PowerFlex 70 Start-Up Make a selection 1. Sign in Already have an account?

Share this post Link to post Share on other sites. Deutsch Dieses Instruktionsblatt kann in mehreren Sprachen unter http: See page 39 for information on other start-up routines. You can Upload the parameters from the drive to the HMI Page 40 Running S. Factory default setting is 12 volts. Don’t have an account? Install original HMI on the dn drive? If the source is an analog input, check wiring of the command.

Scripting must be enabled to use this site.

To print the manual completely, please, download it. Yellow Flashing, An inhibit condition exists, the drive cannot be started. Step 1 Read the General Precautions Powerflex series medium voltage ac drives pages. Most drives will have a jumper storage area inside the front cover. Sign up for a new account in our community. The status of this input is interpreted by drive software. If you have an LCD HIM, two methods are provided, allowing the user to select the desired level needed for the application.


The information provided Does Not replace the User Manual and is intended for qualified drive service personnel only. Specific drive catalog numbers are listed below: To avoid em electric shock hazard, verify that the voltage on the bus capacitors has discharged before performing any work on the 02a.

Address the condition that caused the fault. If the application requires the drive to be disabled without software interpretation, a hardware enable configuration can be utilized. Steady Drive running, no faults are present. Then put that HMI into the new drive and Download the parameters into the new drive.

The drive has been listed by U. Also See for PowerFlex 70 Reference manual – pages User manual – pages Installation instructions manual – 56 pages. Do not reduce wire gauge when using higher temperature wire.

Register a new account.

Related Posts